RO-100MP 4 Stage Pumped Reverse Osmosis System 100gpd (16lph)

From £181.99

  • RO booster pump guarantees optimum filtration by providing the RO membrane with perfect flow
  • Up to 400 litres per day of refined water, ideal for aquatic life, hydroponics, home brewing and steam irons
  • Upgraded deionisation resin stage completely removes TDS from water at higher capacities
  • Easy to transport and simple to setup on site

SKU N/A Category

The Pumped Series are systems pre installed with RO booster pumps to supply the RO membrane with ideal pressure, ensuring optimum output from the system. All RO systems can be purchased with customisable consumables. Some are designed to target specific contaminants, eg. Chloramine, and others are rated at increasing efficiencies depending on the quality of your source water, and how long you would like your filters to serve for.

Larger than our slim range of systems, the RO-100MP utilises a larger final polishing stage with colour change deionisation resin, compared to only the smaller inline final stage in the slim systems. These types of systems range from our smallest of 50 gallons per day up to 100 gallons per day. Above this capacity, there is no deionisation resin stage and the third cartridge on the bottom housing is occupied by another pre filtration stage to aid the reverse osmosis process.

Pump Care

Do not run a pump continuously for more than 4 hours or allow a pump to run dry. Doing so will cause the pump to overheat and become damaged. So that you do not need to manually turn the system on and off every 4 hours, we suggest installing a timer to give the pump a thirty minute break so that it will cool down. We also recommend you install a low pressure switch before your pump so that it does not run dry with little feed flow. A pump should also be mounted using the built in mounting holes to stop the pump from getting damaged through uncontrolled vibration.

If any of the above directions are not followed, the warranty of the pump will be null and void. We will ask for evidence of you following the above directions and will not issue a warranty replacement without any.

System Specifications:

  • System Dimensions mm – H 435 x W 357 x D 200
  • System Weight kg – 8.9
  • Inlet Connection – 1/4″ Pushfit
  • Outlet Connection – 1/4″ Pushfit

 

Membrane Specifications:

  • Permeate Flow Rate gpd (lph) – 100 (16)
  • Active Area m^2 – 0.54
  • Typical Rejection Rate – 97%
  • Maximum Recommended Recovery – 33%
  • Operating Pressure bar (psi) – 3 – 6 (43 – 87)
  • Operating Temperature °C (°F) – 5 – 45 (41 – 113)
  • Feed Flow Rate lpm – 1.9 – 9.1
  • Free Chlorine Tolderance ppm – <0.1
  • PH Range – 3 – 10
  • PH Range (Chemical Cleaning) – 2 – 11
  • Maximum Feed Silt Density Index SDI – 5
  • Maximum Feedwater Turbidity NTU – < 1
  • Recommended Shelf Life – 2 Years

 

Pump Specifications:

  • Pump Model – TYP-2600
  • Flow gpd (lph) – ≥ 400 (63.1)
  • Inlet Pressure bar (psi) – 2.1 (30)
  • Working Pressure bar (psi) – 5.6 (80)
  • Voltage V DC – 24
  • Power Supply Voltage – 24
  • Working Current A – ≤ 1.4
  • Maximum Current A – ≤ 1.95
  • Power Supply Current – ≤ 1.95
  • Port Size – 3/8″ FNPT
  • Dimensions L mm – 202
  • Dimensions H mm – 85
  • Dimensions W mm – 111
  • Weight kg – 2.1
  • Particle Filter – 5 micron polypropylene pre filter traps large particulates
  • Carbon Cartridge – Activated carbon block reduces chlorine, taste, odour and organic impurities
  • RO-1812-100 Membrane – RO Membrane Reduces heavy metals, salts, bacteria and viruses
  • DI Resin Stage – Final Water polishing will clean the last remaining ions in the water and will change colour when it needs replacing
  • 100gpd Booster Pump – Forces water through the system at a pressure that will guarantee optimum filtration
  • RO and Filter Housing Spanners – Making membrane and filter replacements quick and simple to carry out
  • 5M Tubing – 5 meters of 1/4″ tubing makes initial setup simple and accommodates for multiple locations
  • Flow Restrictor – Applies back pressure to the membrane to increase the permeate (pure) water production and decrease the concentrate (waste) water production.
  • Low Pressure Switch – Prevents the booster pump from becoming damaged due to low input water pressure
  • High Pressure Switch – Automatically switches the system off when back pressure is detected
  • Automatic Flush Valve – The ability for the system to automatically flush the RO membrane will prolong the life of the RO Membrane by reducing the chances of it fouling
  • Flush Valve – The ability of manual flushing regularly will prolong the life of the RO Membrane by reducing the chances of it fouling
  • Drain Saddle Valve – To connect the system waste outlet to your property’s drainage
  • Feed Water Connector – To connect the system inlet to your property’s water supply

You might also like

Product Search